We strip soot, paint, graffiti, efflorescence, and staining from brick, stone, and building facades with a mobile laser. No water blasting. No sand. No substrate damage. EPA RRP Lead-Safe Certified and fully insured, on-site across NJ, NY and PA.
Pressure washing looks harmless. It is not. High-pressure water drives moisture deep into porous brick and mortar joints. That trapped water freezes in winter, expands, and spalls the face off the brick. On old lime mortar, the stream cuts the joints out and the wall needs repointing.
Sandblasting is worse. Abrasive grit strips the hard fired skin off the brick and exposes the soft core underneath. The wall looks clean for a season, then soaks up water faster than before and decays from the inside. On carved stone and terracotta, blasting erases the detail for good.
Chemical cleaning trades one problem for another. Acids brighten brick but burn the mortar, etch glass, and leave salts behind that bloom back to the surface as efflorescence weeks later. The runoff is hazardous, and you pay to contain and haul it away.
Pressure washing forces water into the joints and traps moisture in the wall, which freezes and spalls the brick. Laser is dry. Nothing soaks in, so there is no freeze-thaw damage and no drying time before you recoat or repoint.
Sandblasting erodes the fired outer skin of the brick and speeds decay. The laser is non-contact. We tune it to lift soot, paint, and staining while the brick, stone, and mortar underneath stay whole.
No sand, no acid, no runoff to contain or haul away. We capture removed material at the source with HEPA filtration. By the project, laser costs less, because you pay for the cleaning, not the containment and cleanup.
We start with a test patch. Every masonry surface reacts differently, so we tune pulse power and scan speed on a small area and confirm the result with you before we clean the full wall.
The pulsed fiber laser delivers short bursts of energy that vaporize soot, paint, and biological staining off the surface. The energy is matched to the contaminant, so the brick, stone, or mortar underneath reflects it and stays cool and intact.
We capture airborne particulate at the source with HEPA filtration. On lead paint, we follow EPA RRP containment and hand you the documentation. You get a clean, dry surface ready for sealing, repointing, or repainting the same day.
Brick and masonry are porous and fragile. Our laser lifts the contaminant and leaves the wall intact. We remove:
Older brick, terracotta, and cut stone do not survive abrasive cleaning. Blasting erases tooling marks and carved detail, and pressure washing floods the soft historic mortar. Our laser cleans historic facades without grit, water, or chemicals, so the original surface and its detail stay whole.
Buildings from before 1978 often carry lead paint. We are an EPA RRP Lead-Safe Certified Firm. We contain the work, capture the debris, and hand you the compliance file with the finished wall. That protects your occupants and your liability.
We bring the laser to your site across New Jersey, New York, and Pennsylvania. In South Jersey that includes brick cleaning in Pennsauken, Camden, Cherry Hill, and the rest of Camden County. We cover facade work in Philadelphia, Trenton, New York City, Long Island, and the Hudson Valley. Mobilization runs 48 hours, and we scope most jobs from photos and a site address.
Price depends on the surface area, the contaminant, and access. By the hour, laser runs higher than a pressure washer. By the project, it usually costs less, because there is no media to buy, no containment to build, no water damage to repair, and no waste to haul. We quote the total project cost for free.
No, when the parameters are set correctly. The laser is non-contact and tuned to the contaminant, not the masonry. We confirm the setting on a test patch before cleaning the full wall. There is no grit to erode the face and no water to flood the joints.
Yes. We lift the surface salt deposits with the laser. Efflorescence returns when water keeps moving through the wall, so we flag any moisture source we see, since cleaning alone will not stop a recurring leak.
Yes. The laser removes spray paint and tags from brick, block, and stone without the shadowing or surface damage that grinding and chemical strippers leave behind.
Yes. Laser is the gentlest option for landmark brick, terracotta, and stone, and it preserves carved detail. For lead paint on older buildings, we work as an EPA RRP Lead-Safe Certified Firm and provide the compliance documentation.
New Jersey, New York, and Pennsylvania. That includes Pennsauken, Camden County, and South Jersey, plus Philadelphia, New York City, and the surrounding counties. Mobilization runs 48 hours.
Gentle laser cleaning for landmark brick, terracotta, and stone.
Remove paint and coatings from brick, stone, and metal.
Coating-ready surfaces for restoration and repainting.